What Kind Of Carpet Is Used For Speaker Boxes

Covering a Speaker Enclosure

Covering a speaker enclosure with carpeting isn't hard but will crave some (read: lots of) patience the first time you practise it. I volition encompass (no pun intended) the nuts here. I'k sure at that place are many means to do information technology. This is how I've washed it in the past. Attempt all of the following on scrap pieces of wood and carpet the start fourth dimension.

Carpet Selection:
Carpet will have a wide range of backings. For covering speaker enclosures, the worst has a solid rubber backing. It is very difficult to piece of work with. It doesn't bend sharply and is much more hard to cut. Information technology should be avoided at all costs. Some other blazon of backing is the type used for household carpet. it's much more flexible than the solid rubber blazon and is easier to cut simply is withal hard to work with. The all-time is the well-nigh unremarkably used blazon (big surprise) for covering enclosures. At outset glance, you might think it has the poorest quality but it'south actually very skilful. Information technology has a thin flexible, stretchable backing. You tin really run across through it if you lot hold it upwards to a vivid lite. It allows y'all to brand squeamish clean corners that lay downwardly nicely and stay down. It's also cuts very easily. It can exist purchased from virtually whatever auto audio dealer that builds enclosures. If there are no dealers in your immediate expanse, Select Products has several unlike types of carpet that will work well.

Selecting an Adhesive:
Many installers use spray agglutinative for enclosures. It works adequately well when covering the enclosure with vinyl or material or even the very low-cal carpet but I've been, generally, dissatisfied with it'south long term belongings abilities. For heavier carpet, it won't work well at all. One advantage that it has is... it's less time consuming to employ (very of import if you're making a living doing installs). My agglutinative of choice is contact cement. It will agree (virtually) forever and isn't affected by heat. If you've never used contact cement, it must be applied to BOTH of the pieces that are to be joined. The glue is then allowed to dry out until it is no longer sticky to the touch. If it strings when y'all touch it, it'south not dry enough. Afterwards it's dry (about v-fifteen minutes depending on conditions), the parts are put together. You must go on in mind that the parts volition permanently bond to each other on 'contact' (hence the name). If ane tiny betoken touches, yous 'might' exist able to pull it off but if a large piece makes contact, solvent (acetone or mineral spirits) will accept to be used to intermission the bail. You tin use a roller or a castor to apply the cement. Read the High Force per unit area Laminate page for more than options on applying the cement to the woods. I've used Weldwood Contact Cement in the by and never had whatsoever trouble with it. If information technology'southward available in your area, it would be a good choice.

Annotation on Contact Cement:
All contact cement uses solvents which accept to evaporate for the agglutinative to become 'dry'. When the solvent evaporates, it causes the surface to cool. If the humidity is sufficiently high (like it is here in Louisiana), there will exist condensation on the surfaces. This moisture causes the bond to be weak. If the humidity is high in your area because it'southward been raining, it will be better if yous wait for a better (less humid) twenty-four hour period. If the humidity is high considering you live in a humid region or it'southward a cold, damp day, y'all may have to use a heat gun to keep the surfaces warm and moisture costless. If you do employ a rut gun, brand sure that there is a LOT of ventilation. Even if the contact cement is 'non-combustible', you nevertheless need a lot of ventilation.

Cutting Tools:
There are several tools that will make the job easier. The first is a skillful sharp knife. Virtually people apply a razor knife which works fairly well. The biggest problem is that the blades tiresome very quickly. I use a 1" wide putty knife sharpened on i edge with a very crude sandpaper on a belt sander. It allows a quick resharpening of the knife throughout the job and holds the border much ameliorate than a razor knife. There are also knives that have snap-off blades that will requite you a new edge when the end of the blade is snapped off. The following is such a knife and is available from Stanley tools.

Important! When working with any knives but specially this type of knife, get into the habit of retracting the blade the instant that you lot finish the cut. It'due south non natural at first and may seem to be a bit of a pain but if yous get into the habit, yous won't even realize that you're doing it. These knives can do a lot of damage very quickly only if you remember to immediately retract the blade, there's very trivial risk of causing damage or injury.

----- Critically Important -----

Adobe has deemed that the Flash content on web pages is too risky to be used by the general internet user. For nigh all mod browsers, support for Wink was eliminated on 1-1-2021. This means that those browsers volition not display whatever of the interactive Flash demos/calculators/graphics on this (or whatever other) site.

The simplest (not the best) fix, for now, is to download the Ruffle extension for your browser. It will return the Flash files where they were previously blocked. In some browsers, y'all will take to click on the big 'play' push button to make the Flash applets/graphics visible.

An alternative to Ruffle for viewing Flash content is to use an alternative browser like the older, portable version of Chrome (chromium), an older version of Safari for Windows or i of several other browsers. More information on Wink capable browsers can be found Here. It's not quite as simple as Ruffle but anyone fifty-fifty moderately familiar with the Windows Command Console and installation of software tin can use Flash as information technology was intended.

Another cutting tool that you lot'll demand is a practiced pair of heavy duty pair of scissors. They volition be needed to make some of the longer cuts and for cut backlog material out of your fashion. If you tin can't discover a pair that will cutting your carpet, you tin become by with a skilful pocketknife alone. As a side note... If yous're living with your parents, don't use your mom's practiced scissors. If yous do, you lot will NEVER hear the end of information technology. :-)

The Piece of cake Part:
The easiest part of covering the enclosure is, more often than not, covering the pinnacle, front, lesser and back. First, you simply cut a slice long enough to wrap around the enclosure (plus a few inches). Then yous apply contact cement to both pieces (carpet and wood) and wrap the rug around the box stretching information technology tight every bit y'all go. The seam should be on the bottom. Where the 2 ends meet on the lesser of the enclosure, let them overlap. Then, with a Abrupt knife, cut through both of the overlapped pieces (all of the way to the wood). Cutting both pieces at one time makes them fit together perfectly. After cutting, there will be a piece of chip on the height and a piece of scrap underneath the flap of carpet that's going to remain. You lot'll lift the flap and remove the scrap piece. Then you'll glue the flap down. If the box has been completely covered with contact cement, you can apply wax paper to prevent the scrap piece from being bonded to the enclosure. Well, it should look something like what's shown in the demo beneath (clicking the buttons volition go through the different steps).

IMPORTANT! When working with any knives only specially this type of knife, become into the habit of retracting the blade the instant that y'all end the cut. It's not natural at outset and may seem to exist a bit of a hurting just if you get into the habit, you won't even realize that you're doing information technology. These knives tin can practice a lot of damage very quickly but if yous remember to immediately retract the blade, there's very little risk of causing damage or injury.

Unlike Methods of Covering the Ends of the Enclosure

Simplest Method:
The simplest method of getting the ends of the enclosure to look good is to screw a board covered with carpet onto the end of the enclosure. When using this method, you'll simply have to get out a couple of inches of extra carpet sticking off of the end of the enclosure. The extra is folded over to the end of the enclosure. When the covered lath is screwed to the enclosure (from the within of the enclosure), the pieces that you lot folded over will exist covered and and the ragged ends volition no longer exist visible. If y'all want, you tin can but pull the carpet tight and staple the ragged ends to the inside of the comprehend lath (no gluing). I strongly recommend predrilling the ends of the enclosure and then the screws volition be able to pull the comprehend lath tightly to the enclosure. The pigsty has to exist large enough to to let the screw's threads to pass cleanly but not so large that the head volition pull through. Exercise non predrill the covered lath.

Inset board:
This method takes a little more foresight but isn't really any harder. In the following diagram, you can see that end of the enclosure is gear up in slightly (the thickness of the cover board plus the thickness of 2 layers of carpet. Yous again screw the panels to the enclosure with screws from the inside. The finished enclosure looks a little improve because in that location isn't the small gap between the cover board and the enclosure.

Another View

Cut Overlap:
This blazon of finish is the virtually difficult. It requires a peachy deal of forethought when folding the carpet over and cutting the backlog. The cuts are the aforementioned equally the straight cutting in the demo above (with overlapped layers) but are done diagonally from the corner of the side of the enclosure to the center of the side of the enclosure. If done properly, the entire end of the enclosure will appear to take no cuts. Afterward yous're finished, running your paw back and forth over the cuts will fluff up the fibers and make the cuts disappear. The cuts could follow virtually any pattern just, many times, it comes out something like the dark dashed line on the following diagram. If you lot want to endeavour this method and information technology doesn't come out well, y'all tin can always use the 'simplest method' to cover your mistakes.

You May Exist Interested in My Other Sites

This site was started for pages/information that didn't fit well on my other sites. Information technology includes topics from backing up computer files to small engine repair to 3D graphics software to basic data on diabetes.
This site introduces you lot to macro photography. Macro photography is aught more than the photography of small objects. It tin can take quite a while to sympathize the limitations associated with this blazon of photography. Without assist, people will struggle to get proficient images. Understanding what's possible and what's non possible makes the task much easier. If yous need to photograph relatively modest objects (half dozen" in acme/width down to a few thousandths of an inch), this site will help.
If you're interested in air rifles, this site will introduce you to the types of rifles available and many of the things you'll need to know to shoot accurately. It also touches on field target competition. There are links to some of the better sites and forums as well as a collection of interactive demos.
This site helps anyone new to computers and anyone with a basic understanding of computers with a desire to learn more virtually the internal components of a estimator. If you take a computer that you'd like to upgrade but don't know where to starting time, this is a good site for you lot.
This site is for those who want to brainstorm racing karts merely don't fully understand how the various parts work. It'south mostly interactive demos that show how the various parts of the kart work.